About Blackline Inc.

Northwest slurry seal specialists since 1987

Blackline Inc. specializes in slurry seal — a preventative asphalt treatment placed with dedicated slurry equipment. We have done this work since 1987, for private parking lots, HOAs, driveways, and public agencies.

For private parking lots, HOAs, and driveways, we serve the Portland metro and SW Washington. We also work with public agencies across the Northwest. Our office is in Woodland, Washington. We are licensed, insured, and bonded in Washington, Oregon, and Idaho.

Cody Lorenzen, President, is your point of contact for quotes and project questions at (360) 225-1080 or Cody@blacklineinc.net.

What slurry seal is

Slurry seal is a preventative pavement maintenance treatment made of asphalt emulsion, fillers, water, and aggregate. These materials are loaded on site in an automated slurry seal machine that mixes the required type of emulsion, rock size, and fillers according to the project requirements and a laboratory mix design. As slurry seal is applied continuously out of the back of a spreader box, the application fills in any loss of fines and provides a new, durable wearing surface that is cost-efficient. The thickness of the surface depends on the type of slurry seal required.

Types of slurry seal

Type I — A fine aggregate, used on newer asphalt. It provides a minimum of 1/8 inch of new wearing surface. New parking lots, new asphalt roads, and airport runways often use this type to protect the asphalt.

Type II — Used where the surface has had some wear and a loss of matrix. It provides a minimum of 1/4 inch wearing surface after replenishing the fines. It is used to correct moderate to severe raveling, oxidation, and loss of fines, and it provides a skid-resistant surface. This is the most commonly used application.

Type III — Used on moderate- to heavy-traffic asphalt. After filling in lost fines, it provides a minimum of 3/8 inch wearing surface. It is also used to correct severe raveling, oxidation, and loss of fines, and to provide skid resistance. Main thoroughfares and collector roads use this size.

Stop wasting money on seal coat

Seal coat (sometimes called sealcoating) is a thin coating brushed or sprayed onto asphalt. It can darken the surface for a while. It is not the same product as slurry seal, and it is not applied with the same equipment.

Slurry seal is a preventative pavement maintenance treatment made of asphalt emulsion, fillers, water, and aggregate. Those materials are loaded on site in an automated slurry seal machine that mixes the emulsion, rock size, and fillers to the project requirements and a laboratory mix design. The mix comes out of a spreader box as a continuous application. It fills in the loss of fines and provides a new, durable wearing surface. Thickness depends on the type of slurry seal required:

Type I — A fine aggregate, used on newer asphalt. It provides a minimum of 1/8 inch of new wearing surface. New parking lots, new asphalt roads, and airport runways often use this type to protect the asphalt.

Type II — Used where the surface has had some wear and a loss of matrix. It provides a minimum of 1/4 inch wearing surface after replenishing the fines. It is used to correct moderate to severe raveling, oxidation, and loss of fines, and it provides a skid-resistant surface. This is the most commonly used application.

Type III — Used on moderate- to heavy-traffic asphalt. After filling in lost fines, it provides a minimum of 3/8 inch wearing surface. It is also used to correct severe raveling, oxidation, and loss of fines, and to provide skid resistance. Main thoroughfares and collector roads use this size.

If you were quoted a cheap “seal coat” for a parking lot, HOA street, or driveway, ask whether it is actually slurry seal — mixed with aggregate, placed with a slurry machine, and built to a mix design. If it is not, you are not getting the same treatment.

Where we work, and how we’re licensed

For private work, we serve the Portland metro and SW Washington. We are licensed, insured, and bonded in Washington, Oregon, and Idaho:

Washington — BLACKI*135CP

Oregon — CCB 66384

Idaho — PWCL 009681-B-4

Physical office: 9605 Old Pacific Hwy, Woodland, WA 98674

Mailing: P.O. Box 820648, Vancouver, WA 98682

See our projects → /projects

Request a quote → /contact